Imagine gaining SSH access to an old Debian server running on MIPS architecture. Somewhere deep in the network lies a web admin panel, and the objective is to scan the internal network, reach that panel, and obtain valid credentials. For a penetration tester this represents a classic scenario: the first compromised host often conceals an entire infrastructure.
In this article the full chain is examined, from initial reconnaissance to proxy configuration, network scanning, and the attack on the web interface. The material provides methodology and key techniques without supplying a ready-made solution; specific parameters must be determined independently.
The methodology is explained, yet the best way to internalize it is to execute the scenario hands-on. Precisely this sequence, from SSH access on a MIPS host to capturing the hidden admin panel, can be practiced in the One Task exercises of the free course “White Hacker Profession.” References to practical exercises appear throughout the text.
MIPS Architecture and Why It Changes the Rules
MIPS is not an architecture commonly found on laptops. It is, however, widespread in routers, IoT devices, and embedded systems. Old Debian servers on MIPS remain a reality in networks where hardware has not been updated for years.
For a penetration tester this implies three consequences: standard binaries from Kali will not execute; nmap cannot be invoked directly; MIPS binaries or proxying are required; operations must be performed in a minimal BusyBox environment without a compiler and with a 2014 kernel.
Initial Reconnaissance: Where to Begin
The first action after SSH connection is environment enumeration. uname -a reveals architecture and kernel version. ip addr and ip route display interfaces, IP addresses, and the gateway. Checking /proc/sys/net/ipv4/ip_forward shows whether packet forwarding between interfaces is enabled; a value of 0 indicates it is disabled and tunnels are necessary. On the server in the exercise this parameter cannot be changed due to insufficient privileges.
Separately, the correct subnet to scan must be identified. Interfaces and the routing table indicate neighboring networks and the gateway leading to the internal segment, yet the target subnet is usually stated in the task conditions. Careful verification prevents scanning the wrong octet range and wasting time on empty space.
BusyBox systems contain a reduced command set. Availability of wget, curl, scp, ssh, and nc should be verified. A package manager is typically absent. Enumeration determines the entire subsequent plan.
Proxying: Why SSH Forwarding Fails and How to Replace It
SSH supports creation of a SOCKS proxy via dynamic forwarding (-D). In this task, however, such capabilities are disabled in the SSH server configuration and the user lacks rights to modify it. This situation occurs frequently during real penetration tests.
The universal workaround is Chisel, a Go binary that functions as a client-server pair and establishes a TCP tunnel with SOCKS5 support. Chisel provides builds for all architectures, including MIPS in both big-endian and little-endian variants.
The scheme involves running the Chisel server on the attacker machine and the Chisel client on the MIPS server. The client initiates the connection, which is required when direct inbound access to the MIPS server from outside is impossible.
Downloading and Execution
The Chisel server for x86_64 is downloaded to the attacker machine while the MIPS client is obtained for the target. Architecture is confirmed with uname -m, usually mips (big-endian). The file command verifies the binary before transfer via scp or wget. Available memory on the host must also be considered, as Chisel is relatively large yet fits within several hundred megabytes.
Client and server versions must match to avoid compatibility errors. On older MIPS systems newer Chisel versions may crash with segmentation faults because recent compilers generate instructions unsupported by the 2014 kernel. Rolling back to an earlier version is recommended. If no version works, the BusyBox SSH client can be used for reverse port forwarding.
Once the tunnel is established, a SOCKS5 proxy appears on the attacker machine. Verification is performed with curl --socks5 against a target URL.
Scanning the Internal Network Through the SOCKS Proxy
With the tunnel active, the web admin panel must be located. Running nmap through proxychains without correct flags produces timeouts, false positives, and missed ports. ICMP ping does not traverse SOCKS, so host discovery must be disabled.
Working options include:
- proxychains + nmap with mandatory flags -sT (TCP connect), -Pn (no ping), and -n (no DNS resolution);
- executing a static MIPS nmap binary directly on the compromised host;
- using a lightweight SOCKS5-compatible port scanner;
- limiting scans to key ports (80, 443, 8080, 8443) to avoid saturating the narrow tunnel.
Excessive parallel connections should be avoided to prevent exhaustion of file descriptors. A reasonable limit is approximately 16 concurrent connections, with increased timeouts.
Accessing the Admin Panel and Password Guessing
Once the web server is identified, traffic is routed as follows: Firefox → Burp Suite → SOCKS5 proxy → target network. In Firefox the HTTP proxy points to Burp Suite while Burp Suite itself forwards through the Chisel SOCKS5 tunnel.
Review of the admin panel source code typically reveals a simple POST form with username and password fields lacking encryption or CSRF tokens, which is common in legacy internal services.
Password guessing begins with obvious combinations such as admin/admin. If unsuccessful, targeted brute-force is performed via Burp Intruder or curl with --socks5. Response length serves as the success indicator. When the Burp chain proves unstable, the scheme can be simplified to direct SOCKS5 from Firefox or direct use of curl.
Successful credential submission yields the flag. The primary difficulty lies not in exploiting a vulnerability but in establishing access through an atypical architecture.
Validate Knowledge in Practice
Understanding the pivoting scheme on paper differs from independently compiling Chisel for MIPS, constructing the proxy chain, locating the admin panel, and obtaining the password. The complete scenario can be practiced in the Forgotten Server task from the One Task series in the free “White Hacker Profession” course, which replicates the same constraints: an old Debian MIPS server, disabled SSH forwarding, minimal available tools, and a hidden web admin panel.
